Fitting
How to Measure for a Custom Wig Cap
What do you need before you start?
- A soft fabric tape measure. Not a metal one.
- Clips or pins, and a wig cap if the client will wear one.
- A form with one line per measurement.
- A mirror.
Prepare the hair the way it will sit under the finished wig. Wrap or braid long hair flat. A ponytail or bun distorts the numbers.
What are the six standard measurements?
Most wig makers ask for these six. Names for the points differ slightly, so check the manufacturer's form first.
| Measurement | Where the tape goes | What it decides |
|---|---|---|
| 1. Circumference | Around the whole head: from the center of the front hairline, behind one ear, around the nape, behind the other ear and back to the start. | Overall cap size. |
| 2. Front to nape | From the center of the front hairline, straight back over the crown, to the center of the hairline at the nape. | Cap depth from front to back. |
| 3. Ear to ear across the forehead | From the hairline in front of one ear, along the front hairline, to the same point at the other ear. | Width and shape of the front edge. |
| 4. Ear to ear over the top | From the top of one ear, straight over the crown, to the top of the other ear. | Cap depth from side to side. |
| 5. Temple to temple around the back | From one temple, around the back of the head at its fullest point, to the other temple. | How the cap wraps the back of the head. |
| 6. Nape of neck | Across the nape hairline, from one corner to the other. | Width of the bottom edge of the cap. |
How do you take each measurement well?
- Find the hairline first. If the front hairline is hard to see, or the client has hair loss there, ask her to raise her eyebrows. The cap edge usually sits just above the highest forehead crease.
- Keep the tape flat. It should lie against the head with no twists and no gaps.
- Snug, not tight. The tape should touch the head all the way around without pressing into it.
- Check in the mirror. At the back, the tape should sit on the nape hairline, not below it.
- Measure twice. Take every measurement a second time. If the two differ, take a third.
- Write it down at once. Include the unit.
What are the common mistakes?
| Mistake | What goes wrong | Do this instead |
|---|---|---|
| Measuring over a bun or loose hair | The cap comes out too big or lumpy. | Flatten the hair as it will be worn under the wig. |
| Pulling the tape tight | The cap is small and presses on the head. | Keep the tape snug and flat. |
| Confusing the two ear-to-ear measurements | The front edge and the depth are swapped. | Label them "across forehead" and "over top". |
| Mixing inches and centimeters | The numbers cannot be trusted. | Use one unit and write it on every line. |
| Adding "a bit extra" yourself | The manufacturer adds ease again and the cap is loose. | Send true measurements. Let the manufacturer allow for ease. |
What should you send the manufacturer?
- All six measurements, labeled, with the unit.
- What the client wears under the wig: her own hair wrapped, a wig cap, or a bare scalp.
- How much hair she has, and where. Hair loss changes how a cap grips.
- Anything unusual about the head shape: a flat or prominent crown, a high or low nape, uneven sides.
- Where she wants the front edge to sit, if her own hairline is high, low or absent.
- The cap construction you want. See lace top vs skin top wigs.
- Clear photos of the front, both sides and the back, if the client agrees.
If the manufacturer has its own measurement form, use it. Keep a copy on the client's record, and measure again before a repeat order.
Where do we fit in?
We manufacture high-end wigs for brands. Cap construction is one of the custom options, along with color, length, density, and your label and packaging. Every piece is made by hand in our own workshops in New York and Israel. Next, read how to choose wig length, density and color and our manufacturer checklist, or see how it works.
Questions people ask
How many measurements does a custom wig cap need?
Six is the usual set: circumference, front to nape, ear to ear across the forehead, ear to ear over the top, temple to temple around the back, and the width of the nape. Some manufacturers ask for more or fewer, so check their form first.
Which wig measurement matters most?
Circumference. It sets the overall size of the cap. The other measurements shape the cap so it sits correctly at the hairline, ears and nape.
Should I measure in inches or centimeters?
Use whichever unit your manufacturer asks for, and write the unit next to every number. Do not mix units on one form. If you are not told, ask before you measure.
Should I add extra room to the measurements?
No. Send the true measurements, taken with the tape snug but not tight. Tell the manufacturer what the client will wear under the wig, and let them decide how much ease the cap needs.